控制系统通用综合测试系统组建研究

在分析系统需求和基本功能的基础上 ,采用VXI总线技术、远程测控技术和测试应用程序自动生成等关键技术 ,按照综合测试的总体要求进行系统集成 ,组建控制系统通用综合测试系统 ,包括系统硬件和软件方案 ,对系统的硬件结构方案、模件选型以及软件流程、组成和作用进行了详细讨论。     

线阵CCD平场校正及FPGA实现的研究

为了消除由于照明光源的非均匀性、镜头渐晕及CCD传感器噪声对图像质量造成的不良影响,首先从理论上分析了线阵CCD固定模式噪声和像素光电响应非均匀性的数学模型和产生的原因;对像素光电响应非均匀性这一主要影响因素,根据其光电响应模型提出了CCD像素光电响应非均匀性的两点校正方法,即求解出各个像素光电响应不均匀性的校正因子和暗偏置量系数,进而用以计算各个像素的校正量,实现逐点校正;针对校正算法大数据量、实时计算的要求,设计了基于现场可编程逻辑门阵列FPGA快速实现校正算法的硬件处理结构。最后,通过仿真和实验表明,两点校正方法可以有效地减小CCD像素光电响应不均匀性的图像噪声,提高图像质量,以便做后续精确处理。     

不同温度下TC21钛合金等离子表面渗Cr层的摩擦磨损性能

为提高TC21合金的摩擦磨损性能，采用双辉等离子冶金技术在TC21合金表面制备渗Cr改性层，利用扫描电镜(Scanning electron microscope,SEM),能谱仪(Energy dispersive spectromenter,EDS),显微硬度仪和划痕仪等研究了渗Cr层的组织形貌特征、硬度及结合强度，并 在20,300,500 ℃条件下使用摩擦磨损试验机对基体及渗Cr层的摩擦磨损性能进行对比、探究，并分析磨损机理。结果表明：渗Cr层厚度为30μm，均匀致密，与基体结合力至少能承受64 N的垂直载荷；改性层表面硬度超过1 000 HV0.1，约为基体的3倍；TC21合金渗Cr后，不同温度下的减摩性能和耐磨性能均得到提高。在室温下TC21基体磨损机理主要是磨粒磨损、粘着磨损和氧化磨损，而渗Cr层的磨损机理主要是磨粒磨损；500 ℃时基体粘着磨损和氧化磨损程度变得更加严重，渗Cr层磨损机理是剥层磨损和氧化磨损。      

Multi-mode optimal fuzzy active vibration control of composite beams laminated with photostrictive actuators

Firstly, a multi-field coupling finite element formulation of composited beam laminated with the photostrictive actuators is developed in this paper. Moreover, an optimal fuzzy active control algorithm is also proposed on the basis of the combination of optimal control and fuzzy one.This method opens a new avenue to resolve the contradiction between the linear system control method and nonlinear actuating characteristics of photostrictive actuators. The desired control for suppressing multi-modal vibration of photoelectric laminated beam is firstly obtained through optimal control and then the fuzzy control is used to approach the desired mechanical strain induced by photostrictive actuators. Thus, the multi-mode vibration control of beam is realized.In the design process of optimal fuzzy controller, the design of fuzzy control is independent of optimal control. The simulation results demonstrate that the proposed control method can effectively realize multi-modal vibration control of photoelectric laminated beams, and the control effect of optimal fuzzy control is better than that of optimal state feedback control.     

RNSS/INS深耦合高动态导航接收机测试方法研究CSCD

卫星导航和惯性导航采用深耦合方式实现导航作为世界上最先进的导航形式,在国防中的应用越来越广泛,但其在高动态下的性能需要验证。当前针对深耦合高动态下导航接收机的测试研究较少,本文介绍了基于卫星信号模拟器的测试系统组成及测试用高动态场景,运用模拟测试原理,通过对导航接收机在高动态下定位速度和跟踪灵敏度的测试及其结果分析,验证了导航接收机的深耦合功能,对此类接收机的测试方法进行了初步探究。     

系列化构型运载能力设计余量留取方法研究

调研了美国航天型号研制中设计余量留取的情况,结合系列化构型论证工作,对运载能力设计余量留取问题进行了初步研究,分析了关键参数对运载能力的影响,针对不同目标轨道、系列化构型的差异,探索得到了运载能力设计余量差异化留取的方法。     

轴流压气机吞水后的性能变化研究

为了探究航空发动机吸入雨水后压缩系统的特性变化,针对水滴进入压气机后的湿压缩过程展开研究。基于两相流动的基本原理构建了气液两相的传热传质模型和颗粒运动模型,采用一维逐级叠加的方法计算压气机各级性能,并利用Fortran程序对吞雨后压气机整体性能进行了计算。计算结果表明当吞雨量从3%增加到15%时,压气机压比的下降幅度分别由5.7%增加至15.7%;压气机各级温比的变化特性揭示了液滴在压气机前面级蒸发小、后面级蒸发大的规律;通过对比干、湿压缩条件下的压气机整体特性,可得出吞雨后压气机稳定工作范围变窄的结论。     

冲压发动机油箱气路系统长期贮存密封性能研究

为了研究长期贮存对冲压发动机油箱气路系统密封性能的影响,使用流导计算公式推导得到了典型密封结构的漏率计算公式,并通过漏率定义推导得出了长期贮存压差迭代计算公式,对油箱气路系统的典型密封结构在长期贮存条件下的密封能力进行了研究。结果表明,密封结构的漏率主要受内外压差和密封具体形式的影响,现有的密封结构可以保证贮存10年后油箱内气压下降不超过原始压力的0.15‰。计算结果与试验结果的一致性很好,证明了现有油箱气路系统密封方案的合理性。     

Hypervelocity impact induced shock acoustic emission waves for quantitative damage evaluation using in situ miniaturized piezoelectric sensor network

Manmade debris and natural meteoroids, travelling in the Low Earth Orbit at a speed of several kilometers per second, pose a severe safety concern to the spacecraft in service through the HyperVelocity Impact(HVI). To address this issue, an investigation of shock Acoustic Emission(AE) waves induced by HVI to a downscaled two-layer Whipple shielding structure is performed,to realize a quantitative damage evaluation. Firstly a hybrid numerical model integrating smoothparticle hydrodynamics and finite element is built to obtain the wave response. The projectiles, with various impact velocities and directions, are modelled to impact the shielding structure with different thicknesses. Then experimental validation is carried out with built-in miniaturized piezoelectric sensors to in situ sense the HVI-induced AE waves. A quantitative agreement is obtained between numerical and experimental results, demonstrating the correctness of the hybrid model and facilitating the explanation of obtained AE signals in experiment. Based on the understanding of HVI-induced wave components, assessment of the damage severity, i.e., whether the outer shielding layer is perforated or not, is performed using the energy ratio between the regions of ‘‘high frequency" and ‘‘low frequency" in the acquired AE signals. Lastly, the direct-arrival fundamentalsymmetric wave mode is isolated from each sensing signal to be input into an enhanced delay-andsum algorithm, which visualizes HVI spots accurately and instantaneously with different sensor network configuration. All these works demonstrate the potential of quantitative, in situ, and real time HVI monitoring using miniaturized piezoelectric sensor network.     

Crystal orientation and morphology of a lamellae in wrought titanium alloys: On the role of microstructure evolution in b processing

To obtain high-quality aviation forgings of titanium alloys, b forging is an essential processing step which must be considered throughout a production process. In this work, the effect of b forging on the crystal orientation and morphology of lamellar a was experimentally investigated in a two-phase titanium alloy. Strong dynamic recovery during b working resulted in the formation of low-angle grain boundary(LAGBb) inside b grains. The lamellar a can penetrate through the LAGBb, leading to similar intra a LAGBs on subgrain boundaries. Deformation banding occurs at high strain rates, and both diffusive and sharp boundaries of deformation bands can be observed.A continuous change of the b orientation in diffusive boundaries results in the formation of fine and disordered a lamellae without intra-lamellar boundary to hold the Burgers orientation relationship(OR). On sharp boundaries, it is prone to producing continuous grain boundary a(aGB) with a highly similar orientation along the boundaries. Meanwhile, there may exist several lower-angle boundaries within the grain boundary a for a smoother orientation change on the b grain boundary.